Dell U3421WEB 34 Inch UltraSharp Curved USB-C Monitor Instruction Manual
DELL U3421WEB
Disassembly Procedures
S1 Turn off power
S2 To remove the stand:
- Place U3421WE monitor on U3417Wcurve sponge jig.
- Press and hold the stand release button.
- Lift the stand up and away from the monitor.
S3 Unlock 4 screws on Rear Cover
S4 Use hands or Bar Scraper to disassemble Rear Cover from Middle Frame
Notice the disassembly order:
Left Side=>Top Side =>Right Side =>Bottom Side
S5 Pull out “CTRL BD FFC” from I/F BD to take off Rear Cover
S6 Tear off a tape from Rear Cover
Tear off “CTRL FFC” from Rear Cover
Unlock 3 screws to disassemble CTRL BD from Rear Cover
S7 Unplug “Backlight Wire” from LED
Driver BD and tear off a tape from Panel (See Red mark)
Unplug “Speaker Wire” from I/F BD (See Pink remark)
Tear off 5 tapes from “Speaker Wire” and Panel (See Green Mark)
Unlock 6 screws to disassemble Speaker from Middle Frame (See yellow mark)
S8 Tear off a conduct tape from Main SHD and Panel
S9 Tear off an acetate tape from “USB BD Wire” and Panel
Unplug “USB BD FFC” and “USB BD Wire” from I/F BD
Unlock 1 screw to disassemble USB BD from Middle Frame
Unplug “USB BD FFC” and “USB BD Wire” from USB BD
S10 Disassemble a gasket from Panel
S11 Unlock 4 screws to disassemble Main SHD from Panel
S12 Tear off an acetate tape from “FFC EDP” and panel
S13 Tear off a yellow tape from the “FFC EDP” connector
Unplug “FFC EDP” from panel
Take off Main SHD from Panel
S14 Unlock 21 screws to disassemble.
Middle Frame from Panel.
S15 Tear off 4 tapes from “Backlight Wire”
S16 Unplug “Backlight Wire” from panel.
Disassemble 8 pieces of “BOSS PANEL” from the panel.
S17 Disassemble Mylar from Main SHD
S18 Unlock 10 PCBA screws to disassemble “I/F BD”, “SPS BD” and “LED Driver BD” from Main SHD
S19 Unplug wires from I/F BD, SPS BD and LED Driver BD
S20 Remove electrolyte capacitors (red mark) from printed circuit boards
S20-1 Cut the glue between bulk caps. and PCB with a knife
S20-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB
S20-3 Take out bulk cap. pin solder with soldering iron and absorber
S20-4 Lift the bulk cap. up and away from the PCB
Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
| Capacitors/condensers (containing PCB/PCT) | No used |
| Mercury-containing components | No used |
| Batteries | No used |
| Printed circuit boards (with a surface greater than 10 square cm) | The product has printed circuit boards (with a surface greater than 10 square cm) |
| Component contains toner, ink and liquids | No used |
| Plastic containing BFR | No used |
| Component and waste contain asbestos | No used |
| CRT | No used |
| Component contain CFC, HCFC, HFC and HC | No used |
| Gas discharge lamps | No used |
| LCD display > 100 cm2 | Product has an LCD greater than 100 cm2 |
| External electric cable | Product has external cables |
| Component contains refractory ceramic fibers | No used |
| Component contains radioactive substances | No used |
| Electrolyte capacitors (height > 25mm, diameter > 25mm) | Product has electrolyte capacitors (height >25mm, diameter > 25mm) |
Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.
Tool Description:
- Screwdriver
- Penknife
- Bar scraper
- U3417W Curved Sponge Jig