D-Link 8-Port Gigabit Unmanaged Desktop PoE Switch DGS-1008P User Guide
DGS-1008P
8-Port Gigabit Unmanaged Desktop PoE Switch
User Guide
About This Guide
This guide provides instructions on how to install the D-Link DGS-1008P 8-Port Gigabit Unmanaged Desktop PoE Switch.
Terms/Usage
In this guide, the term “Switch” (first letter capitalized) refers to the DGS-1008P while “switch” (first letter lower case) refers to other Ethernet switches. Some technologies use the terms “switch”, “bridge”, and “switching hubs” interchangeably. All of these terms are commonly accepted for referring to Ethernet switches.
Copyright and Trademarks
Information in this document is subject to change without notice.
© 2020 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
Product Introduction
The DGS-1008P Switch provides 8 Gigabit Ethernet ports, 4 of which support Power over Ethernet (PoE) for PoE applications such as powering wireless Access Points (APs), IP cameras, and IP phones. The remaining 4 non-PoE ports can be used to connect devices such as computers, printers, and Network Attached Storage (NAS) to the network. With wire-speed Gigabit throughput, the DGS-1008P provides non-blocking switching for both home and office environments.
IEEE 802.3af/at Power over Ethernet
The first four ports of the DGS-1008P support the IEEE 802.3af and IEEE 802.3at PoE protocols. Each of these four ports can directly supply up to 15.4 watts of power to an IEEE 802.3af-compliant Powered Device (PD) or up to 30 watts of power to an IEEE 802.3at-compliant Powered Device (PD). This effectively minimizes the clutter of extra cables and is especially suitable for expanding the network with remote devices that are otherwise too far away from a power outlet.
Easy to Use, Safe, and Excellent Performance
The DGS-1008P is a plug-and-play device that requires no additional configuration after installation. Support for auto-MDI/MDI-X on all ports eliminates the need for crossover cables when connecting to other switches or hubs. Auto-negotiation on each port senses the link speed (either 10, 100, or 1000 Mbps) of a connected network device and intelligently adjusts for improved compatibility and optimal performance. The fanless design of the DGS-1008P extends the device’s lifetime while also significantly reducing noise when operating. The DGS-1008P also features a set of diagnostic LEDs which display the status and activity of each port on the device, allowing the user to quickly detect and correct problems if they occur.
The DGS-1008P features several safety functions to prevent an unexpected overload of PoE power. In the event of such an overload, the Switch will immediately cut off the power supply to any connected powered device, protecting both the PoE device and the Switch from being damaged.
All ports on the DGS-1008P are Gigabit-capable, providing a larger bandwidth for high-speed network applications, especially IEEE 802.11n access points, high-resolution video cameras, and IP phones. Combining the convenience of PoE, superior performance, and ease of use, the DGS-1008P is the ideal PoE solution for expanding both home and small business networks.
Package Contents
The package contents should include the following items:
- 1 x D-Link DGS-1008P Switch
- 1 x AC to DC power adapter with power cord
- 1 x multilingual Quick Installation Guide
- 1 x wall mounting kit
- If any item is found missing or damaged, please contact your local reseller
Product Overview
Front Panel
| Item | Description |
| Ports 1 to 4 | These are 10/100/1000 Mbps PoE-capable ports, used for connecting Ethernet devices and PoE-powered devices. |
| Ports 5 to 8 | These are 10/100/1000 Mbps non-PoE ports, used for connecting Ethernet devices. These ports cannot power PoE devices. |
Table 2 – Front Panel Interfaces
Rear Panel
| Item | Description |
| Kensington Security Lock |
This is a built-in physical Kensington security lock. |
| SWITCH GND | This screw is used to secure a grounding wire to connect the Switch to the ground. |
| DC Power Jack | Input jack for the power adapter. |
Indicator LEDs
| LED | Status | Description |
| Power | Solid green | The Switch is powered and working. |
| Off | The Switch is turned off. | |
| PoE Max. | Solid red | This indicates the total PoE power output of the Switch has exceeded the Guard Band threshold of 73 watts but is still below the total budget of 80 watts. For more information on the Guard Band feature, please refer to Understanding the Switch Features. |
| Blinking red | This indicates the total PoE budget of 80 watts has been exceeded. When the Switch’s PoE budget is being fully utilized, no additional devices can be powered through the Switch. When the user unplugs a Powered Device (PD) from the DGS-1008P, lowering the total PoE output to less than 73 watts, the PoE Max LED will turn off. The remaining available PoE budget can then be used to power another powered device. | |
| Off | The current PoE power consumption is below the 73 watts Guard Band threshold. | |
| PoE | Solid green | The port is providing power to a connected powered device (PD). |
| Solid red | The PoE power feed from this port has failed as a result of one of the following possible causes: / Insufficient total PoE budget. Overcurrent: The maximum allowed current of the power device was exceeded. Short circuit: The powered device has short-circuited. | |
| Off | No PoE-powered device is connected to this port | |
| Link/Act/Speed (ports 1 to 8) | Solid green | There is an active link operating at 1000 Mbps on this port. |
| Blinking green | There is traffic on the port at 1000 Mbps. | |
| Solid amber | There is an active link operating at 10/100 Mbps on this port. | |
| Blinking amber | There is traffic on the port at 10/100 Mbps. | |
| Off | There is no active link on this port. |
Table 3 – Indicator LEDs
Hardware Installation
This chapter provides installation information for the D-Link DGS-1008P.
Installation Precautions
- For safe switch installation and operation, it is recommended to:
- Visually inspect the DC power jack and make sure that it is fully secured to the power adapter.
- Make sure that there is proper heat dissipation and adequate ventilation around the switch.
- Install the Switch in a site free from strong electromagnetic sources, vibration, dust, and direct sunlight.
- Not place heavy objects on the Switch.
Grounding the Switch
This section describes how to connect the Switch to the ground. It is necessary to complete this procedure before powering on the Switch.
Required Tools and Equipment
- One ground screw (attached to the back panel).
- Ground cable (not included in the accessory kit): The grounding cable should conform to local and national installation requirements. Depending on the power supply and system, a 12 to 6 AWG copper conductor is required for a US installation. Commercially available 6 AWG wire is recommended. The length of the cable depends on the proximity of the Switch to proper grounding facilities.
- A screwdriver (not included in the accessory kit).
The following steps explain the procedure for connecting the Switch to a protective ground:
- Verify that the system is powered off.
- Use the ground cable to place the #8 terminal lug ring on top of the ground screw opening, as seen in the figure below.
- Insert the ground screw into the ground screw opening.
- Using a screwdriver, tighten the ground screw to secure the ground cable to the Switch.
- Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding stud or bolt on the rack where the Switch is installed.
- Verify that the connections from the ground connector on the Switch to the rack are securely attached.
Attaching the Rubber Pads
The DGS-1008P comes with a strip with 4 adhesive rubber pads to place on the bottom of the device to prevent the Switch from damaging the surface it is placed on. This allows the Switch to be placed on virtually any flat surface. To attach the rubber pads, simply remove the rubber pads from the adhesive strip and stick one pad on each corner on the bottom panel of the Switch.
Mounting the Switch on a Wall
The DGS-1008P can also be mounted to a wall for more convenient placement. Please follow the instructions below for more information on how to mount the device to different types of walls.
Mounting the Switch on a hard surface wall (e.g. brick, cement)
- Drill two holes that align with the keyholes on the back of the Switch in the wall where you want to mount the DGS-1008P and place the two included nylon screw anchors into the drilled holes.
- Drive the two screws included in this package into the placed nylon anchors.
- Hook the mounting keyholes on the back of the Switch onto the screws to secure the device to the wall.
Mounting the Switch on a soft surface wall (e.g. wood)
- Drive the two screws included in this package in the wooden wall where you want to mount the DGS1008P so that they align with the keyholes on the back of the Switch.
- Hook the mounting keyholes on the back of the Switch onto the screws to secure the device to the wall.
Powering on the Switch
After connecting the switch to the network using a compatible network cable such as Cat.4/5/5e, simply connect the Switch to a power outlet to activate the device.
Understanding The Switch’s Features
Power over Ethernet (PoE)
The DGS-1008P supports many PoE features to guarantee the safety and stability of the Switch and the connected powered devices.
PoE Power Budget: The total PoE budget of the DGS-1008P is limited to a maximum of 80 watts to both protect the Switch and to stabilize the power being transmitted to the PoE-powered devices.
PoE Port Priority: The DGS-1008P is configured to have predefined PoE priorities for all PoE ports to prevent events such as unexpected overloading on PoE ports. Lower port numbers have a higher priority for supplying power, for example port 1 > port 2 > port 3 > port 4. When a PoE overload is detected, the power supply from the higher number ports will be cut off first.
Guard Band: The DGS-1008P reserves a 7 watts Guard Band to prevent the power supply from exceeding the PoE power budget. When the Switch detects the current PoE output has reached 73 watts, the PoE Max.
LED will light up solid red and the Switch will not supply power to new connected devices.
For example: When Port 3 to 4 are both feeding 30 watts of power to the attached clients (total PoE power used = 60 watts), and a new powered device is connected to port 1 that is being supplied more than 13 watts of power, the Switch will not supply the power to Port 4 device.
Power Saving
The DGS-1008P supports IEEE 802.3az Energy Efficient Ethernet (EEE), which constantly monitors all ports for data transmission and will put inactive ports in sleep mode to save power.
Appendix A – Technical Specifications
Hardware Specifications
Key Components / Performance
- Switching Capacity: 16 Gbps
- Max. Forwarding Rate: 11.90 Mpps
- Forwarding Mode: Store-and-forward
- Packet Buffer memory: 192 Kbytes
Port Functions
8 10/100/1000Base-T ports compliant with the following standards:
– IEEE 802.3
– IEEE 802.3u
– IEEE 802.3ab
– IEEE 802.3x (full-duplex flow control)
– IEEE 802.3af (Ports 1 to 4)
– IEEE 802.3at (Ports 1 to 4)
– IEEE 802.3az Energy Efficient Ethernet
– Supports backpressure in half-duplex mode
Physical & Environment
- Dimensions: 190 x 120 x 38 mm
(5.5 x 3.0 x 1.06 inch) - Weight: 0.59 kg (1.30 lbs)
- Power adapter AC input: 100 to 240 V AC,
50/60Hz - Device DC input: 54 V DC, 1.67 A
- Acoustic: 0 dB (fanless)
- Operation Temperature
– Device: 0 to 50 °C (32 to 122 °F)
– Power adapter: 0 to 40 °C (32 to 104 °F) - Storage temperature -40 to 70 °C
(-40 to 158 °F) - Operation humidity: 0% to 95% RH
- Storage humidity: 0% to 95% RH
Emission (EMI) Certifications
FCC class B
CE Class B
VCCI Class B
RCM
BSMI
Safety Certifications
LVD
BSMI
Features
General Features
- Supports up to 4K MAC addresses
- Jumbo frame: Supports up to 9216 bytes
- Supports 802.1p Quality of Service (QoS) with 8 strict queues
- Cable diagnostics
PoE Features
- IEEE 802.3af/at-compliant
- Supplies up to 15.4 watts of power to powered devices via ports 1 to 4, or up to 30 watts on two ports simultaneously.
- Total PoE budget: 80 watts.
- PoE port priority
Appendix B – Regulatory Statements
FCC Warning
This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense.
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class B digital apparatus complies with Canadian ICES-003.
VCCI Warning
This is a product of VCCI Class B Compliance.
SAFETY INSTRUCTIONS
The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details.
Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
Do not attempt to service the product and never disassemble the product. For some products with a user-replaceable battery, please read and follow the instructions in the user manual.
Do not spill food or liquid on your product and never push any objects into the openings of your product.
Do not use this product near water, areas with high humidity, or condensation unless the product is specifically rated for outdoor application.
Keep the product away from radiators and other heat sources.
Always unplug the product from mains power before cleaning and use a dry lint-free cloth only.
Disposing and recycling your product
D-Link and the environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
D-Link recommends that you always switch off or unplug your D-Link products when they are not in use. By doing so you will help to save energy and reduce CO2 emissions.
To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com.