Yamaha SWP2-10MMF L2 Switch Owner’s Manual

YAMAHA SWP2-10MMF L2 Switch

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
   This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifica-tions not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “A” digital devices. Compliance with these require-ments provides a reasonable level of assurance that your use of this product, in a commercial environment, will not result in harmful interference with other electronic devices. However, operation of this product in a residential area is likely to cause interference in some form. In this case you, the user, bear the responsibility of correcting this condition.
   This product generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the opera- tion of other electronic devices. Compliance with FCC regula-tions does not guarantee that interference will not occur in all installations. If this product is found to be the source of inter-ference, which can be determined by turning the product
   “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
   Relocate either the product generating the interference or the device that is being affected by the interference.
   Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
   In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
   If these corrective measures do not produce satisfactory results, please contact the local retailer that is authorized to distribute this type of product. If you can not locate the appro-priate retailer, please contact Yamaha Corporation of Amer-ica, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
   The above statements apply ONLY to those products distrib-uted by Yamaha Corporation of America or its subsidiaries.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for
future reference.
This product is designed for audio network. Do not use for any purposes other than the one intended. Those who are unfamiliar with handling or those who can not handle according to this manual such as children, should be supervised by responsible persons to ensure safety.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
If you notice any abnormality

• If any of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet.
  • The power cord or plug becomes frayed or damaged.
  • Unusual smells or smoke are emitted.
  • Some object, or water has been dropped into the product.
  • Cracks or other visible damage appear on the product. Then have the product inspected or repaired by qualified Yamaha service personnel.

Power supply/Power cord

• Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the product. The required voltage is printed on the name plate of the product.
• Use only the supplied power cord/plug.
• If you intend to use the product in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
• Make sure to fully insert the electric plug to prevent electric shocks or fire.
• This product receives power from multi sources. When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately disconnect the all plugs from the outlet.
• Remove the electric plug from the outlet when the product is not to be used for extended periods of time.
• Do not touch the product or the electric plug during an electrical storm.
• Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock, fire, or damage.
• If you plan to connect a powered device that complies with the IEEE802.3 at standards, use a CAT5e or higher-grade cable. Failure to observe this precaution could result in a fire or malfunction.

Do not open

• This product contains no user-serviceable parts. Do not attempt to disassemble the internal parts or modify them in any way.

Water warning/Fire warning

• Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings.
• Never insert or remove an electric plug with wet hands.
• Do not place any burning items or open flames near the product, since they may cause a fire.

Hearing loss

• When turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid hearing loss and speaker damage. When turning the power off, the power amplifier should be turned off FIRST for the same reason.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others. These precautions include, but are not limited to, the following:

Power supply/Power cord

• When removing the electric plug from the product or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.

Location and connection

• Do not place the product in an unstable position or a location with excessive vibration, where it might accidentally fall over and cause injury.
• Do not block the vents. This product has ventilation holes at the sides to prevent the internal temperature from becoming too high. In particular, do not place the product on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the product(s), or even fire.z
• When installing the product:
  • Do not cover it with any cloth.
  • Do not install it on a carpet or rug.
  • Make sure the top surface faces up; do not install on its sides or upside down.
  • Do not use the product in a confined, poorly-ventilated location.
    Inadequate ventilation can result in overheating, possibly causing damage to the product(s), or even fire.
• If the product is mounted in an EIA standard rack, carefully read the section “Precautions for Rack Mounting” on page 9. Inadequate ventilation can result in overheating, possibly causing damage to the product(s), malfunction, or even fire.
• Do not place the product in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the product, remove all connected cables.

Maintenance

• Remove the power plug from the AC outlet when cleaning the product.

Handling caution

• Do not insert your fingers or hands in any gaps or openings on the product (vents, panel, etc.).
• Do not rest your weight on the product or place heavy objects on it.
• This product uses class 1 lasers.
  Do not look into the tip of an optical fiber or into an optical connector. Doing so may damage your eyes.

Backup battery

• Do not replace the backup battery by yourself. Doing so may cause an explosion and/or damage to the product(s). When the backup battery needs to be replaced, contact your Yamaha dealer and have qualified Yamaha service personnel replace the backup battery.

NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.
Handling and maintenance

• • Do not use the product in the vicinity of a TV, radio, mobile phone, or other electric products. Otherwise, the product, TV, or radio may generate noise.
  • Do not expose the product to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
  • Condensation can occur in the product due to rapid, drastic changes in ambient temperature—when the product is moved from one location to another, or air conditioning is turned on or off, for example. Using the product while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the product for several hours without turning on the power until the condensation has completely dried out.
  • Do not place vinyl, plastic or rubber objects on the product, since this might discolor the panel.
  • When cleaning the product, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
  • Drain all static electricity from your clothing and body before handling the device. Static electricity can damage the device. Touch an exposed metal part of the host device or other grounded object beforehand.
  • Do not install the product in a location where magnetic fields are strong. Otherwise, it might cause the product to malfunction.
  • Do not connect any noise generating devices on the same power line as the product. Failure to observe this precaution could result in a malfunction or damage to the product.
  • Do not locate any connected LAN cables close to the power cord. Otherwise, high voltage might be induced, resulting in malfunction.
  • A 1000BASE-T connection will require an Enhanced Category 5 (CAT5e) or better LAN cable.

Saving data

• This unit has a built-in backup battery that maintains time information for the data. When the backup battery runs down, the time information will be initialized, causing incorrect time information to be recorded in the log. If this occurs, contact your dealer or a Yamaha customer service center to have the backup battery replaced. The life span of the backup battery is approximately 10 years, but this may vary depending on the conditions of use. Set the clock after replacing the battery. Data maintained by the backup battery:
• Time information.

Information

About copyrights

• Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer.

About functions/data bundled with the product

• This is a class A product. Operation of this product in a residential environment could cause radio interference.
• This product is a class 1 laser product. It is compliant with IEC/EN 60825-1, IEC/EN 60825-2, FDA 21 CFR 1002.10, and 1040.10. IEC 60825-1:2014
  Factory: Axcen Photonics Corporation 6F., No.119, Baozhong Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)

About this manual

• The illustrations as shown in this manual are for instructional purposes only.
• Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
• Software may be revised and updated without prior notice.

About disposal

• This product contains recyclable components. When disposing of this product, please contact the appropriate local authorities.

Open Source Software Used in this Product

• Please refer to Yamaha Pro Audio website for the details of licensing article.
  http://www.yamahaproaudio.com/

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the top of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.

SOFTWARE LICENCE AGREEMENT

This agreement is an agreement between you, the customer, and Yamaha Corporation (hereafter referred to as “Yamaha”) defining the conditions under which Yamaha provides firmware for this Yamaha network product (hereafter referred to as the Product) and related programs, printed material, and electronic files (hereafter referred to as the Software).
The Software may be used only for the purpose of operating it on the Product or on a personal computer or similar device. This agreement applies to the Software provided by Yamaha to the customer and to copies of the Software created by the customer in compliance with section 1 subsection (1) of this agreement.

Permission to use

1. The customer may install and use the Software on a Product or a personal computer or similar device owned by the customer.
2. With the exceptions that are explicitly defined by this agreement, the customer shall not permit the reuse of, sell, distribute, rent, lease, lend, or transfer the Software, nor upload it to any website or server where it could be accessed by specified or unspecified numbers of people, nor duplicate, translate, adapt it, or rewrite it into any other program language. The customer shall not correct, revise, reverse-assemble, reverse-compile, or perform any reverse engineering of the Software, and may not cause any third party to perform such actions.
3. The customer shall not modify, erase, or delete the Yamaha copyright indications that are included in the Software.
4. With the exceptions that are explicitly defined by this agreement, Yamaha does not grant or permit the customer any of Yamaha’s intellectual property rights.

Property rights
The Software is protected by copyright law and by other laws, and is the property of Yamaha. The customer hereby agrees that no property rights or intellectual property rights related to the Software are granted by Yamaha to the customer by this agreement nor any other means.
Export restrictions
The customer shall abide by all applicable export regulations and rules of the relevant countries, and shall not export or re-export the Software, neither in part nor in whole, in violation of any applicable rules and regulations.
Support and updates
Yamaha, its subsidiaries, their sales representatives and dealers, and any other party handling or distributing the Software do not accept any responsibility for maintaining the Software nor for supporting the customer’s use of the Software. Nor do the aforementioned parties have any responsibility to update the Software, to fix bugs, or to provide support.
Limitation of responsibility

1. The software is licensed for use “in its current state (as-is).” Yamaha, its subsidiaries, their sales representatives and dealers, and any other party handling or distributing the Software make no warranty, neither explicit nor implicit, regarding the merchantability or suitability of the Software for any particular purpose.
2. Yamaha, its subsidiaries, their sales representatives and dealers, and any other party handling or distributing the Software shall bear no responsibility for any damages
   (including but not limited to lost profit and any other consequential or incidental damages) that may arise from the use of or inability to use the Software. This shall be the case even if Yamaha, its subsidiaries, their sales representatives and dealers, or any other party handling or distributing the Software had been informed of the possibility of such damages.
3. Yamaha, its subsidiaries, their sales representatives and dealers, and any other party handling or distributing the Software shall bear no responsibility for any dispute between the customer and a third party that may arise from or related to the use of the Software.

Term of validity

1. This agreement shall continue in force until it is terminated by the following sub-sections (2) or (3).
2. The customer may terminate this agreement by deleting all instances of the Software that are installed on the Product or on a personal computer or similar device.
3. This agreement shall immediately terminate if the customer violates any of the terms of this agreement.
   Upon the termination of this agreement due to sub-section
4. above, the customer shall immediately delete all instances of the Software that are installed on the Product or on a personal computer or similar device.
5. Regardless of any clauses of this agreement, the provisions of sections 2 through 6 of this agreement shall continue in force even after the termination of this agreement.

Separability
Even if any clause of this agreement should become invalid, the remainder of the agreement shall remain in force.

U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:

The Software is a “commercial item,” as that term is defined at 48 C.F.R. 2.101 (Oct 1995), consisting of “commercial computer software” and “commercial computer software documentation,” as such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the Software with only those rights set forth herein.

General articles
The customer agrees that this agreement is the complete and only declaration of agreement between the customer and Yamaha regarding all matters prescribed by this agreement, and that it takes precedence over all proposals, prior agreements, or any other communication between the customer and Yamaha, whether oral or written. No change to this agreement shall have any force unless it is signed by a representative who is duly authorized by Yamaha.

Jurisdiction
This agreement shall be under the jurisdiction of the laws of Japan, and shall be interpreted according to those laws.

Features

• Recommended settings for Dante are provided
  Recommended settings (such as QoS, EEE, and IGMP Snooping) for stable operation of the Dante network can be specified with only DIP switch. The 10GBASE-SR/LR ports support 10 gigabit, allowing operation without fear of insufficient bandwidth even on a Dante network that is set to a sampling frequency of 96 kHz.
• VLAN presets provided
  Three types of preset VLAN settings are provided, allowing a more stable network to be constructed by dividing audio signals and control signals with a single SWP2 unit. The user can also customize the settings.
• Visualize the network status
  The “Yamaha Audio Network Monitor” Windows application allows you to monitor the status of the network and the Dante devices. The unit’s indicators also show which VLAN is connected to which port.
• Hardware that supports safety and peace of mind
  All models can be rack-mounted. In consideration of temporary setups or other environments in which cables are liable to be pulled out, etherCON and opticalCON are provided as standard. In addition to an AC IN jack with V-lock, an XLR-4-32 type EXT DC INPUT jack is also provided. Redundant power can be provided by using a PA-700 or other external power supply (+24V).

Related software
If you are using VLAN, connect the computer to the VLAN 1 port.

• Yamaha Audio Network Monitor (Windows application)
  This is used to monitor the entire network, including SWP2 data as well as all Dante devices on the Dante network.
  Download this application from the following website. http://www.yamahaproaudio.com/
• Web GUI
  Use this to view or edit the settings of SWP2 units on the network from a web browser.
  Access the Web GUI from the Yamaha Audio Network Monitor.
  To use the Web GUI, connect a computer to the VLAN 1 port.
  When accessing the Web GUI, the “Windows Security” dialog box may appear. With the factory settings, the administrative password is set as follows.

Terms

• VLAN
  This stands for Virtual Local Area Network. A virtual network is constructed separately from the physical connections. When there are multiple networks of differing types, setting up a VLAN allows a logically separate network to be constructed that shares the same physical switches.
  A VLAN can be either a “Port-based VLAN” which constructs groups using a physical connection for each port, or a “Tag VLAN” which differentiates VLAN groups by assigning a tag to each Ethernet frame. In the case of a port-based VLAN, each VLAN requires a connection to communicate with another switch. Using a tag VLAN allows multiple VLANs to be combined into a single trunk connection (cable) that connects switches, ensure that the total amount of data does not exceed 1 Gbps for the LAN ports or 10 Gbps for the 10GBASE-SR/LR ports. The VLAN preset A and B of the SWP2 use tag VLAN.
• Link aggregation
  Link aggregation is a function that bundles multiple LAN/SFP+ ports that connect network devices, and treats them as a single logical interface in order to expand the communication bandwidth. A group that is bundled using link aggregation is called a link aggregation group (LAG).
  Link aggregation is a technology that is useful when multiple communications are occurring. The communications can be distributed between the aggregated connections by using a load balancing function. Since load balancing distributes the load according to IP address, we recommend that you fix the IP addresses of each device in order to stabilize load balancing.
  Even if a problem occurs on one of the LAN/SFP+ ports that are bundled by link aggregation, so that this port is unable to communicate, communication will continue via the remaining ports.
• Trunk
  This function adds tags to multiple VLANs so that they can be transmitted and received via a single connection. When one SWP2 transmits VLAN 1 data via the trunk connection, the SWP2 unit that receives this will transmit the data only to the port that corresponds to its own VLAN 1.
  Communication speed for a metal trunk connection on the SWP2’s VLAN preset B is 1 Gbps per cable. If there is only one cable, and the total bandwidth passing through the trunk connection exceeds
  1 Gbps, packets will be delayed or dropped. Some of the SWP2’s VLAN presets enable link aggregation of the trunk connection. If the bandwidth will exceed
  1 Gbps for a LAN port or 10 Gbps for a 10GBASE-SR/LR port, or if you want to provide redundancy to guard against cable breakage, you should use two trunk cables.

Controls and Functions

Front panel
The explanation here is based on the SWP2-10MMF.

1. LAN ports
   These are etherCON (RJ-45) ports for connecting Ethernet cables (CAT5e or better is recommended). A cable with an RJ-45 connector can also be connected.
   All ports support 1000BASE-T, 100BASE-TX, and 10BASE-T.
2. 10GBASE-SR ports (SWP2-10MMF)/ 10GBASE-LR ports (SWP2-10SMF)
   This is an opticalCON DUO port for connecting an optical fiber cable. LC Duplex connectors can also be connected.
   If you use a cable with an LC Duplex connector, fasten the dust cap attached to the cable connector to prevent dust from adhering when the cable is not in use.
   NOTE
   • Use an opticalCON DUO optical fiber cable made by Neutrik Corporation. Since optical fiber cables are vulnerable to being bent or pulled, you can reduce the occurrence of problems by using a cable that has a strong sheath and is equipped with a locking mechanism.
   • The SWP2-10MMF can use GI-type multi-mode fiber cables that have a core diameter of approximately 50 μm and cladding diameter of approximately 125 μm. The maximum length between devices is 300 m.
   • The SWP2-10SMF can use SM-type single-mode fiber cables with a core diameter of approximately 9 μm and a cladding diameter of approximately 125 μm. The maximum length between devices is 10 km.
   • In some cases, the specifications might not be satisfied because of the optical fiber cables that are used and the conditions of installation.
   • Link up is possible only for 10GBASE-SR/LR between the same standards. 10GBASE-SR/LR can not link up with 1000BASE optical standards.
     Cleaning
     Correct communication might not be possible if debris and/or dust has adhered to the ends of optical fiber cables or the ports. Clean the equipment regularly by using commercially available optical fiber cleaning products.
3. LED mode indicators
   This indicates what the status indicators are showing.
4. [LED MODE] button
   This switches what the status indicators are showing.
5. Status indicators
   These indicate the status of each port. The displayed content depends on the mode. For details on the display in each mode, refer to “Status indicator display.”
6. DIP switches
   These specify startup settings for the unit.
   Set the DIP switches when the power is turned off. The settings are not applied if you change the setting while the power is on.
   The switch illustrations indicate the up/down position as follows.

Caution when using this unit together with another manufacturer’s switch

Dante supports both IGMP V2 and V3, but you must set all switches in the same network to operate using the same version.
If the SWP2 starts up with DANTE settings, it operates using IGMP V3. In this case, if the network includes even one switch that is operating with IGMP V2, problems such as dropouts in the sound might occur.

Switch 2 and 3 (VLAN PRESET)
Specifies the VLAN preset that is used when switch 1 is in the [DANTE] position. This setting is ignored if switch 1 is set to [USER].
If you change the settings via the web GUI or a command, the settings are applied temporarily but is not stored; the next time the unit starts up, it returns to the VLAN preset setting.

In the tables, “1,” “2,” “Tr1,” and “Tr2” respectively indicate VLAN 1, VLAN 2, trunk (LAG1), and trunk (LAG2).
For an explanation of VLAN, trunk, link aggregation, and LAG, refer to Terms on page 10. For details, you can download technical reference material (HTML).

Rear panel

Grounding screw
Since the included power cord has a three-pin plug, this unit will be appropriately grounded if the AC outlet is grounded. In some cases, you may be able to reduce hum noise and interference noise by connecting this screw to ground as well.

AC IN connector

Connect the included power cord here. First connect the power cord to this unit, and then connect the power supply plug to an AC outlet; the SWP2’s internal power supply turns on.
The supplied AC power cord features a V-lock mechanism via a latch, which prevents the power cord from coming off accidentally.
Insert the cable plug all the way until it locks in securely.
Press the latch button on the plug to disconnect the power cord.

[EXT DC INPUT] connector
This is an XLR-4-32 type jack for supplying an external power supply (+24V) as a backup for the SWP2’s internal power supply.
Connect a Yamaha PA-700 AC adaptor or an equivalent product recommended by Yamaha.

CAUTION

• Before connecting the external power supply, you must turn off the external power supply. Failing to do so may cause electrocution or malfunctions.
• EXT DC INPUT connector is intended to be supplied by Power Supply certified with “Limited Power Source” or “LPS” and rated 24 Vdc.

NOTE

• If an external power supply is connected, the SWP2 will operate normally when its internal power supply and the external power supply are on, as well as when only one is on.
• If both power supplies are on, and one of them is interrupted during operation, the unit will continue to operate normally.

LAN ports

VLAN Use Cases

This case double the cables between devices as a safeguard against cable breakage. This diagram shows a setup using VLAN preset C.

Separating control signals from audio signals
This case logically separates control signals such as for Editor or StageMix from Dante’s audio signals, making the network more stable. This diagram shows a setup using VLAN preset B.
If VLANs are not used, and control signals and audio signals flow across the same network, the two will compete for communication bandwidth. In order to prevent such an effect, we recommend that you use VLANs to separate the control signal and audio signal networks.