Electrolux EDI2004 EasyLine Dry Iron Instructions

Electrolux EDI2004 EasyLine Dry Iron

Instruction book

Before using the iron for the first time, please read the safety advice carefully.

Components

1. Power cord protector
2. Handle
3. Water tank release button
4. Spray button
5. Water tank cover
6. Spray nozzle
7. Button-guard
8. Temperature selector
9. Soleplate*
10. Power indicator light

Safety advice

Read the following instruction carefully before using the product for the first time.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory
    or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • The appliance may only be connected to a power supply where voltage and frequency comply with the specifications on the rating plate.
  • The iron is not to be used if it has been dropped, if there are visible signs of damage to the plug, the main cord, to the iron itself or if it is leaking.
  • The appliance must only be connected to an earthed socket.
  • If the appliance or the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified person, in order to avoid hazard.
  • The iron must be used and rested on a stable surface. When placing the iron on it’s stand, ensure that the surface on which the stand is placed is stable.
  • Never leave the appliance unattended while connected to the supply mains.
  • The appliance must be switched off and the main plug withdrawn each time after use, before cleaning and maintenance.
  • The plug must be removed from the socket outlet before the water tank is filled with water.
  • The main cable must not come into contact with any hot parts of the appliance.
  • Do not immerse the appliance in water or any other liquid.
  • This appliance is intended for domestic use only. The manufacturer cannot accept any liability for possible damage caused by improper or incorrect use.

Getting started

  1. Before first use. Remove all adhesive remains and gently rub with a dampened cloth. When turned on for the first time, temporary odours may occur.
  2. Open the water tank cover by pressing the water tank release button. Remove the water tank, fill it with water and then replace it back.
  3. Plug power cable into a power outlet. Power indicator light turns on. Set temperature by turning temperature selector to adequate choice. When the light turns off, iron is ready to be used.
  4. Use spray to pre-dampen fabrics by pressing spray button several times to release a fine mist. Ensure that water tank is at least 1/4 full.
  5. Keep the iron always in vertical position when you are not using it.

Ironing chart

Fabric Temperature setting Ironing recommendation
Acrylic, Acetate, Nylon,

Synthetics, Rayon, Viscose

 Iron on reverse side while still damp or use spray to dampen.
Silk, Cotton blends, Wool & wool blends Iron on reverse side. Use an ironing cloth to prevent shine marks. Check label and follow manufacturer’s instructions. For blends, use setting for the

fibre requiring lowest setting.

Cotton, Corduroy, Linen,

Denim

 Iron while still damp or use spray to dampen. Use ironing cloth to prevent

shine marks, especially with dark colours.

Tips: Always start ironing the fabrics that require low ironing temperature setting, and then increase the temperature setting for fabrics which require higher temperature. The iron heats up faster than it cools down.

Cleaning and care

  1. Always store iron on its heel rest. To clean exterior surfaces, use a damp soft cloth and wipe dry. Do not use any chemical solvents, as these will damage the surface.
  2. Cleaning the soleplate. Do not use scouring pads or harsh cleaners on the soleplate as these will damage the surface. To remove burnt residue, iron over a damp cloth while iron is still hot. To clean the soleplate, simply wipe with soft damp cloth and wipe dry.

Troubleshooting

Problem Possible cause Solution
Soleplate is not heating, even though iron is turned on. Connection problem. Check main power supply cable, plug

and outlet.

Temperature control is in MIN position. Select adequate temperature.
Spray mist feature does not work There is no water on the tank. The water tank must be at least 1/4 full. Fill the iron as described in the section

“Getting Started”

Disposal

Packaging materials
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. PE<, >PS<, etc. Please dispose the packaging materials in the appropriate container at the community waste disposal facilities.

Old appliance
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.