Honeywell FocusPro TH6320R Wireless Thermostat User Manual
Honeywell FocusPro TH6320R Wireless Thermostat
Quick Reference Card
Grasp and pull to see basic operating instructions at a glance.
Battery Holder
Press down and pull to remove batteries. Batteries should be replaced once a year (see page 16).
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50 °F (10 °C).
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
About your new thermostat
Your new thermostat is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed:
CAUTION: EQUIPMENT DAMAGE HAZARD. You can override the program schedule at any time, and manually adjust the temperature (see pages 10-11).
Quick reference to controls
Quick reference to display screen
Set the time and day
- Press SET CLOCK/DAY/SCHEDULE, then press s or t to set clock.
- Press SET DAY, then press s or t to select the day of week.
- Press DONE to save.
Note: If the SET CLOCK/DAY/SCHEDULE option is not displayed, press DONE or CANCEL.
Note: If the display flashes Set Clock, the thermostat will follow your settings for the weekday “Wake” time period until you reset the time and day.
Select the fan setting
Press FAN to select Auto or On. In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously.
Select the system setting
Note: Options may vary depending on your heating/ cooling equipment.
Press SYSTEM to select:
- Heat: Thermostat controls only the heating system.
- Cool: Thermostat controls only the cooling system.
- Off: All systems are off.
- Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
- Em Heat: (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat. Compressor is locked out.
Energy-saving settings for maximum cost savings
This thermostat is pre-set to use energy-saving program settings. We recommend these settings, since they can reduce your heating/cooling expenses. (See next page to adjust times and temperatures of each time period.)
To adjust program schedules
- Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE.
- Press s or t to set your weekday Wake time (Mon–Fri), then press NEXT.
- Press s or t to set the temperature for this time period, then press NEXT.
- Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
- Press NEXT to set Weekend time periods (Sat- Sun), then press DONE to save & exit.
Note: Make sure the thermostat is set to the system you want to program (Heat or Cool).
Program schedule override (temporary)
Press to temporarily adjust temperature.
Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the next programmed time period begins (see page 8). To cancel the temporary setting at any time, press CANCEL.
Program schedule override (permanent)
Press to permanently adjust temperature.
Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods. The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed. Whatever temperature you set will be maintained 24 hours a day until you manually change it, or press CANCEL to resume the programmed schedule.
Auto Changeover
Auto Changeover is a feature used in climates where both air conditioning and heating are often used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation.
Remote control
Temperature is measured at location of remote control
The optional remote control can act as a mobile thermostat, to maintain a comfortable temperature as you move from room to room. When the system is responding to temperatures measured at the Remote, the thermostat will display “Remote has Control.” Press CANCEL to restore temperature control to the thermostat (the system will only respond to temperatures measured at the thermostat).
Note: The thermostat may take up to 15 seconds to respond to commands entered at the remote control. See Remote Control Operating Manual for more information.
Additional features
To display outdoor climate
If you have an outdoor air sensor, press MORE to display the current outdoor temperature and humidity. Press DONE to exit.
To find a lost remote control
If you misplace a remote control, press MORE, then FIND REMOTE. The remote will beep for two minutes to help you locate it. Press anywhere on the display screen to stop the beeping.
Special features
Built-in compressor protection: This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is re-started too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump).
Adaptive Intelligent Recovery: This feature eliminates the guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set.
Note: When Adaptive Intelligent Recovery is in effect, the thermostat will display “Recovery.”
Battery replacement
Note: If batteries are inserted within 2 minutes, the time and day will not have to be reset. All other settings are retained in memory.
Battery replacement (outdoor air sensor)
Replace outdoor sensor batteries when the REPLACE BATTERY OUTDOOR warning begins flashing on the thermostat. The warning flashes about two months before the batteries are depleted. Remove the sensor from the bracket, remove the cover and install 2 fresh AA lithium batteries. After batteries are installed, the sensor will automatically restore communication with the wireless network within a few minutes.
In case of difficulty
Heating or cooling system does not respond
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Wait 5 minutes for the system to respond.
Screen displays “No Signal”
Thermostat has lost radio contact with the wireless network (usually because of a power outage). To restore power:
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
After power is restored, the thermostat will automatically restore wireless communication within a few minutes.
Up to 5-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,
- return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
- call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.
When the product is registered on-line at www.warranty.Honeywell.com, the standard manufacture coverage stated above extends to a period of (5) years.