AEG BK18C 18V High Pressure Inflator Instruction Manual
Original instructions
Please read and save these instructions!
 |
|
TECHNICAL DATA
| Inflator | BK18C |
| Production code | 4778 18 02… … 000001-999999 |
| Battery voltage | 18 V |
| Rated input | 225 W |
| Max. operating pressure | 150 PSI; 10,34 bar |
| Air delivery rate @ 90 psi / 6,21 bar / 621 kPa |
14 I/min |
| Air delivery rate @ 35 psi / 2,41 bar / 241 kPa |
23 I/min |
| Recommended Ambient Operating Temperature | -18°C … +50°C |
| Recommended battery types | L1820R – L1890R; L1820S |
| Recommended charger | BL1218; BLK1218; AL12180; AL18G |
| Pressure hose length | 51 cm |
| Weight without battery | 1,05 kg |
| Weight according to EPTA-Procedure 01/2014 (Li-Ion 2,0 … 9,0 Ah) | 1,52 … 2,21 kg |
| Noise information
Measured values were determined according to EN 62841. Typically, the A-weighted noise levels of the tool are: Sound pressure level (Uncertainty K=3dB(A)) Sound power level (Uncertainty K=3dB(A)) Wear ear protectors! |
89,0 dB(A) 100,0 dB(A) |
| Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841 Vibration emission value ah* Uncertainty K= |
4,0 m/s² 1,5 m/s² |
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However, if the tool is used for diÌerent applications, with diÌerent accessories, or poorly maintained, the vibration emission may diÌer. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched oÌ or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintaining the tool and the accessories, keeping the hands warm, and organization of work patterns.
Wear ear protectors! Exposure to noise can cause hearing loss.
Save all warnings and instructions for future reference.
Always wear goggles and ear protection when using the machine.
Do not leave the appliance unsupervised when it is switched on.
Never direct any compressed air or blow any dust toward people or animals.
Do not use the device in rooms with a potentially explosive atmosphere.
Risk of Bursting. Do not overinÍate. Follow all manufacturer‘s instructions for the item. Do not set the tool to an output pressure greater than the marked maximum pressure of the item to be inÍated.
Never block or plug the air outlet during operation.
Check the air hose for wear or damage before each use. Check all accessory connections are secure.
This appliance can be used by children aged 8 years and above and persons withÏreduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way andÏunderstand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Has the damage been repaired immediately by an authorized workshop?
Following 5 minutes of continuous operation, a short break of at least 5 minutes must be taken to allow the device to cool down. Remove the battery pack before starting any work on the appliance.
To avoid injury and damage, never immerse the tool, removable battery, or charger in liquid or allow liquid to penetrate them. Use only System GBS chargers for charging System GBS battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack, or charger in Íuid or allow a Íuid to Íow inside them. Corrosive or conductive Íuids, such as seawater, certain industrial chemicals, bleach or bleach-containing products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The inÍator is intended to inÍate items such as car tires, bike tires, lawn equipment tires, sports equipment, air mattresses, beach toys, and other inÍatables. Do not use this tool to fill air tanks or shocks. Do not use this tool as a breathing device. Do not use this tool to spray chemicals.
MAINTAINANCE
Remove the battery pack before starting any work on the appliance.
The ventilation slots of the machine must be kept clear at all times. Service and repair work may only be carried out by authorized specialist workshops.
If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the tool still does not work properly, return the tool, charger, and battery pack, to an AEG service facility for repairs.
Use only AEG accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state Article No. as well as the machine type printed on the label and order the drawing at your local service agents or directly at Techtronic Industries GmbH, Max-Eyth-StraßeÏ10,
71364ÏWinnenden, Germany.
BATTERIES
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean. For an optimum lifetime, the battery packs have to be fully charged, after use. Battery packs that have not been used for some time should be recharged before use.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture.
Store the battery packs in a 30% – 50% charged condition. Every six months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or by burning them. AEG Distributors oÌer to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Rechargeable batteries are to be removed from the appliance before being charged;
If the appliance is to be stored unused for a long period, the batteries should be removed.
Exhausted batteries are to be removed from the appliance and safely disposed of.
The supply terminals are not to be short-circuited.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national, and international provisions and regulations. The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusive to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to prevent short circuits. Ensure that the battery pack is secured against movement within the packaging. Do not transport batteries that are cracked or leak. Check with the forwarding company for further advice.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU and the following harmonized standards have been used
EN 62841-1:2015
EN 60335-1:2012+A11:2014+A13:2017+A1:2019
+A2:2019+A14:2019
EN 62233:2008
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
SYMBOLS
| CAUTION! WARNING! DANGER! | |
| Remove the battery pack before starting any work on the appliance. | |
| Please read the instructions carefully before starting the machine. | |
| Wear ear protectors! | |
| Always wear goggles when using the machine. | |
| Risk of Bursting. | |
| Do not dispose of electric tools, batteries/rechargeable batteries together with household waste material. Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point. | |
| Voltage | |
| Direct Current | |
| European Conformity Mark | |
| Ukraine Conformity Mark | |
| Eurasian Conformity Mark |
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Techtronic Industries (UK) Ltd
Parkway
Marlow, SL7 1YL
UK
(01.22)
4931 4259 67
AEG is a registered trademark used under license from AB Electrolux (publ).
