Panasonic R8U4FJ5168Z BTV4.0 Dual Mode USB HCI Module User Guide

User Guide
Panasonic Model: R8U4FJ5168Z
BTv4.0 Dual Mode USB HCI Module
FCC ID: U6YBT850
IC: 216P-BT850

Scope
This document describes an overview of the Panasonic Bluetooth module, R8U4FJ5168Z, and its implementation note for the manufacturer using the module.
Operational description
Panasonic Bluetooth RJM module, R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/R8U3FJ8326Z is a Wireless Bluetooth module that conforms to Bluetooth standards and operates in the unlicensed band at 2.4GHz.
Implementation note
Panasonic Bluetooth module, R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/ R8U3FJ8326Z is designed as a PCBA to be placed into an enclosure.
Panasonic Bluetooth RJM module, R8U4FJ5168Z/ R8U2FJ8436Z is designed to operate with a custom PCB trace antenna. The antenna is listed as follows. The maximum gain of the antenna is -3.4dBi. The antenna impedance is 50 ohms.

Installation and availability
The R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/R8U3FJ8326Z is a sub-assembly that is professionally assembled into passenger aircraft cabins by trained installers qualified to service aircraft. This product is custom-made specifically for passenger aircraft cabins to provide short-range Bluetooth connectivity to the passenger(s) within close proximity and is not listed or offered for sale to the general public.
FCC and IC Regulatory
Documentation Requirements
When integrating the Bluetooth module, R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/R8U3FJ8326Z into the product, the manufacturer shall meet the documentation requirements of FCC and IC. The following outline the labeling information guide and external labels for the product integrates the Bluetooth module, R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/R8U3FJ8326Z.
The manufacturer shall place the following wording on the product and it shall be visible by the customer at the time of purchase.
Contains:
FCC ID: U6YBT850
IC: 216P-BT850
User’s Guide Requirements
The Bluetooth RJM module, R8U4FJ5168Z/ R8U2FJ8436Z/ R8U5FJ8946Z/R8U3FJ8326Z complies with FCC Part 15 Rules for a Modular Approval. The transmitter module must not be located close to any other transmitter or antenna. With the above condition, no other testing is required, but the manufacturer must still have responsibility for the product compliance. In case the above conditions are not met, the FCC authorization is no longer valid and FCC ID is not allowed to be used. For this reason, the manufacturer must have responsibility for the compliance of the end product. When the manufacturer uses the R8U4FJ5168Z module, it must include specific information in the user guide of the product. And manufacturer must not include information on how to install or remove this module in the user guide. Manufacture must also put the following FCC statements without any modification at a prominent place in the user guide.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.
FCC Caution:
Any changes or modifications not expressly approved by Panasonic Avionics Corporation could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Industry Canada
The manufacturer shall place the following wording on the product and it shall be visible by the customer at the time of purchase.
RF Radiation Hazard Warning
Using higher gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be co-located with another transmitter.
This radio transmitter (IC: 216P-BT850) has been approved by Innovation, Science, and Economic Development Canada’s to operate with the antenna types listed in the table above with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Under Innovation, Science and Economic Development Canada’s regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Under Innovation, Science and Economic Development Canada’s regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

General Comments

• There are no user-serviceable parts.
• Service can only be performed by qualified persons.
• There are no components requiring tune-up.
• The antenna is a non-detachable microstrip Di-pole type.

Radio Specification

• Bluetooth (Ver 4.0 Dual Mode Class Bluetooth and BLE
• Frequency of Operation: 2402MHz – 2480MHz
• Modulation BT: FHSS, (GDSK, π/4DQPSK, 8DPSK) (1MHz)
• Modulation LE: GFSK (2MHz)
• Power Supply to Radio: 3.3VDC ~ 1.8VDC
• Antenna Type: Microstrip Antenna (non-detachable Di-pole type)
• Antenna Gain: -3.4dBi, 3dBi, -1.2dBi, 2.7dBi
• Clock Frequency: 48MHz
• Impedance: 50Ω

Panasonic Avionics Corporation
26200 Enterprise Way,
Lake Forest,
CA 92630.