Samsung EP-H5300 Wireless Car Charger User Guide
EP-H5300
Wireless Car Charger
Contains
Quick Guide
- Replace the clip fastener which is optional according to the shape of your car’s air vent(if you need it).
- Set the support frame with the proper angle to suit your car’s air vent.
- Remove the ball joint fastener from the wireless car charger by rotating it counterclockwise.
- Put the clip through the ball joint fastener, and assemble the clip on the wireless car charger.
- Rotate the control knob to adjust the length of the metal hook, so that the wireless car charger which has been assembled already can be locked on the air vent of the car, then connect the USB Type C cable to the port.
- Connect the other end of the cable to the USB-A port of a USB car adapter* that fits into the cigarette lighter socket.
- Put the smart device close to the infrared sensor, and the wireless car charger will open automatically, then attach the smart device to the wireless car charger.
- Press the quick-release button to take the smart device off the wireless car charger.
* Use the enclosed cable for power connection(USB car adapter is sold separately).
Use only Samsung-approved car adapters that support 15W or higher.
* The maximum possible length of the metal hook is 35 mm.
* The indicator will turn red → green → yellow when the wireless car charger powers on.
* Visit www.samsung.com to view the user manual and the safety information.
– Please check the shape of the air vent and the wing length of air vent.
– Do not push or pull the wireless car charger when it has been locked on the air vent.
– Assembly must be completed before installation on air vent.
– Before disassembly, the wireless car charger must be removed from the air vent.
– Before removing the wireless car charger from the air vent, please make sure to release the metal hook.
– Install the wireless car charger at the passenger side air vent so that it does not only interfere with driving but also interferes with vehicle buttons and monitors.
– The manufacturer is not responsible for any damage to the air vent caused by negligence in use.
FCC regulatory conformance
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV for help.
NOTE :
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
RF Exposure
This equipment complies with FCC radiation exposure limits set
forth uncontrolled environment.
Samsung Electronics America, Inc.
85 Challenger Road, Ridgefield Park, New Jersey 07660
Phone: 1-800-SAMSUNG (726-7864)
IC regulatory conformance
This device complies with CAN ICES-3 (B)/NMB-3(B).
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
EU regulatory conformance:
RF exposure information: The EIRP power of the device at EN62479: 2010. RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission Recommendation(1999/519/EC).
Hereby, Lineprinting declares that the radio equipment type EP-H5300 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.samsung.com
UK Regulatory Conformance
Hereby, we(Line printing) declared that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
The product can be used in EU countries without any restriction.
Product specification
Product name: Wireless Car Charger
Model: EP-H5300
Input: 5 V
(Support QC2.0/3.0,PD2.0/3.0,AFC Protocol)
Wireless output: Max 9W of wireless power
Charging speed may vary depending on the device model and condition of the adapter or cable.
Actual charging speed may also vary depending on the actual usage, the temperature inside/outside the vehicle, charging conditions, and other factors.
Operating temperature: -10~40℃
Correct disposal
For information on Samsung’s environmental commitments and product regulatory obligations, e.g. REACH, visit our sustainability page available via www.samsung.com
Your consumer rights are governed by the law of the country in which you purchased the product. Please contact your service provider for more information.
Manufacturer: Jiangxi Line printing Co., Ltd.
Address: No.268,Nantang Road,Jinggangshan Economic
Development Zone, Ji’an City, Jiangxi, China
Leaflet.0813V.1
Printed in China
