Brother FL-Y5M02 WLAN 802.11 ac/b./g/n 1T1R USB Interface Module Installation Guide

brother FL-Y5M02 WLAN 802.11 ac/b./g/n 1T1R USB Interface Module

Product Specification

Interface

Installing the WLAN module driver

NOTE
The illustrations may look different on your operating system.
To install the WLAN module driver, follow the steps below:

Step 1:
Close all other applications before continuing.

Step 2:

1. Insert the WLAN module into the USB port of your computer.
2. When the REALTEK USB Wireless LAN Driver and Utility window appears, click Next.

Step 3:
Follow the on-screen instructions to install the REALTEK USB Wireless LAN driver.

Step 4:
When the installation is completed, select “Yes, I want to restart my computer now.”, and then click Finish.

Setting up the WLAN module driver

Step 1:
On your desktop, click the REALTEK USB Wireless LA.. icon.

Step 2:
In the Available Network tab, select the network you want to connect to.

Step 3:
When the Wireless Network Properties window appears, click OK.

Step 4:
Check the network connection status in the General tab.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
   This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:
   KDB 996369 D03 OEM Manual v01 rule sections:
   1. List of applicable FCC rules
      This module has been tested for compliance to FCC Part 15.
   2. Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.
   3. Limited module procedures
      Not applicable.
   4. Trace antenna designs
      Not applicable.
   5. RF exposure considerations
      This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.
   6. Antennas
      The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.

      Antenna Type	2.4GHz: PIFA antenna with 2.6dBi gain 5.0GHz: PIFA antenna with 3.3dBi  gain
      Antenna connector	IPEX

   7. Label and compliance information
      The final end product must be labeled in a visible area with the following: “Contains FCC ID: NJC-FLY5M02”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
   8. Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification.
   9. Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable.
      As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

   IMPORTANT NOTE:
   This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module.
   A minimum distance of 20 cm must be maintained between the user and the antenna of the integrated module. Under such configuration, the FCC radiation exposure limits set forth for a population/uncontrolled environment can be satisfied.
   Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

   USER’S MANUAL OF THE END PRODUCT:
   In the user’s manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. If the size of the end product is smaller than 8 cm x 10 cm, then additional FCC part 15.19 statement is required to be available in the user’s manual:
   This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

   LABEL OF THE END PRODUCT:
   The final end product must be labeled in a visible area with the following ” Contains TX FCC ID: NJC-FLY5M02 “.If the size of the end product is larger than 8 cm x 10 cm, then the following FCC part 15.19 statement has to also be available on the label:
   This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

   1. this device may not cause harmful interference and
   2. this device must accept any interference received, including interference that may cause undesired operation.

   Manual Information To the End User
   The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
   The end user manual shall include all required regulatory information/warning as show in this manual.

   OEM/Host manufacturer responsibilities
   OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment

   Industry Canada statement

   This device complies with ISED’s licence‐exempt RSSs.
   Operation is subject to the following two conditions:

   1. This device may not cause harmful interference, and
   2. this device must accept any interference received, including interference that may cause undesired operation.

   Radiation Exposure Statement:
   This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.

   This device is intended only for OEM integrators under the following conditions: (For module device use)

   1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
   2. The transmitter module may not be co‐located with any other transmitter or antenna.
      As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end‐product for any additional compliance requirements required with this module installed.

   IMPORTANT NOTE:
   In the event that these conditions can not be met (for example certain laptop configurations or co‐location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re‐evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

   End Product Labeling
   This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 1112C-FLY5M02 ”.

   Manual Information To the End User
   The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

   Caution : 

   1. the device for operation in the band 5150‐5250 MHz is only for indoor use to reduce the potential for harmful interference to co‐channel mobile satellite systems;
   2. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
   3. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725‐5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
   4. where applicable, antenna type(s), antenna models(s), and worst‐case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

   DETACHABLE ANTENNA USAGE

   This radio transmitter [IC: 1112C-FLY5M02] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

   Manufacturer	Model	Antenna Type	Max Gain (dBi)	Impedance (Ω)
   Unictron Technologies Corportation	AA222	PIFA	3.3	50

   European Union regulatory notice
   The telecommunications functionality of this product may be used in the following EU and EFTA countries:
   Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
   Notice for use in Russia
   For 2.4 GHz Wireless LAN operations (802.11 b/g) of this product certain restrictions apply: This equipment may be used indoor for the entire 2400 MHz – 2483.5 MHz frequency band channels (1-13). For indoor use the maximum effective incident radiated power (EIRP) is 100 mW.