TPA-C002P HP Wireless Rechargeable USI Pen Instructions
Instructions
Product Notices
Regulatory Notices
This document provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for your product. Some of these notices may not apply to your product.
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or television technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
For questions regarding this product, write to
HP Inc.
1501 Page Mill Road
Palo Alto, CA 94304
or call HP at 650-857-1501.
To identify your product, refer to the part, series, or model number located on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user’s authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods.
Products with wireless LAN devices or HP Mobile Broadband Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
During normal operation of tablet PCs and notebook computers with displays equal to or less than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC/Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the computer user guides included with your computer.
During normal operation of notebook computers with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC/Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed.
To identify the location of the wireless antennas, refer to the computer user guides included with your computer.
Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:
RED 2014/53/EU; Low Voltage Directive 2014/35/EU;
EMC Directive 2014/30/EU; Ecodesign Directive 2009/125/EC;
RoHS Directive 2011/65/EU. Compliance with these directives is assessed using applicable European Harmonised Standards.
Radiofrequency bands and maximum power levels (select products only)
RadioTechnology | Maximum Transmit Power EIRP (mW) |
Bluetooth: 2.4 GHz | 100 |
NFC: 13.56 MHz | 10 |
Non-specific Short Range Device: 2.4 GHz | 10 |
Note: Use only HP-supported software drivers and correct country settings to ensure compliance.
The point of contact for regulatory matters is HP Deutschland GmbH, HQ-TRE, 71025, Boeblingen, Germany.
Thailand WWAN wireless notice
This telecom equipment has complied with NTC regulations.
Laser compliance
A mouse may contain a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-
- The product does not emit hazardous laser radiation.
Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007; and with IEC 60825-1:2007.
To reduce the risk of exposure to hazardous radiation:
- Do not try to open the module enclosure. There are no user-serviceable components inside.
- Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.
- Allow only HP Authorized service technicians to repair the unit.
Power cord notice
If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country or region.
The power cord must be rated for the product and for the voltage and current marked on the product’s electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 0.75 mm²/18AWG, and the length of the cord must be between 1.0 m (3.2 ft) and 2 m (6.56 ft). If you have questions about the type of power cord to use, contact your authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
Safety Notices
Headset and earphone volume level notice
For your own safety, use headsets or earphones compliant with the headphone limits in EN 50332-2.
When the HP product includes a headset or earphones, the combination is in compliance to EN 50332-1.
Environmental notices
Disposal of waste equipment by users
Battery Section
User-replaceable battery notices
HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, refer to the HP website at http://www.hp.com/recycle.
Taiwan Declaration of the Presence Condition of the Restricted Substances Marking
#1 Group of products: Accessories that have lens function
Camera
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Shell | O | O | O | O | O | O |
Metal part | — | O | O | O | O | O |
Lens | O | O | — | O | O | O |
Input/output device | — | O | O | O | O | O |
Light-sensing component | — | O | O | O | O | O |
Cable | — | O | O | O | O | O |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicates that the percentage content of the restricted substance exceeds the reference percentage value of the present condition Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
#2 Group of products: Accessories that have a speaker function
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Shell | O | O | O | O | O | O |
Metal part | — | O | O | O | O | O |
Speaker | O | O | O | O | O | O |
Cable | — | O | O | O | O | O |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the present condition. Note 2: “0” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
#3 Group of products: Accessories that have a read/write function
CD/DVD/Floppy device, storage device (external HDD/SSD, USB flash drive), docking device, card reader, writing device (stylus, pen), one-to-multiple hub, touch mat, magnetic stripe reader, barcode scanner, fingerprint reader, port replicator/ USB hub
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Shell | O | O | O | O | O | O |
Metal part | — | O | O | O | O | O |
Read/write component | — | O | O | O | O | O |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the present condition. Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
#4 Group of products: Accessories that have PCB as main part
Memory card, network card, graphic card, and other internal add-on cards
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Active component (transistors and integrated circuits) |
— | O | O | O | O | O |
Passive component (resistors and capacitors) |
— | O | O | O | O | O |
Solder | — | O | O | O | O | |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the present condition. Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
#5 Group of products: Other accessories that do not have an outstanding function
Mouse, keyboard, power supply, battery charger, wireless video module, video ingest module
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Shell | O | O | O | O | O | O |
Metal part | — | O | O | O | O | O |
Cable | O | O | O | O | O | |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the present condition. Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
#6 Group of products: Other printer products
Thermal receipt printer
Restricted substances and their chemical symbols | ||||||
Unit | (Pb) | (Hg) | (Cd) | (Cr+6) | (PBB) | (PBDE) |
Circuit board | — | O | O | O | O | O |
Shell | O | O | O | O | O | O |
Metal part | — | O | O | O | O | O |
Print head | O | O | O | O | O | |
Motor | — | O | O | O | O | O |
Paper roller | — | O | O | O | O | O |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the present condition. Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence. Note 3: “—” indicates that the restricted substance corresponds to the exemption. |
© Copyright 2018 HP Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Java is a registered trademark of Oracle and/or its affiliates.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. First Edition:
November 2018
PRINTER: Replace this box with Printed- In (PI) Statement(s) as per spec.
NOTE: This box is simply a placeholder. PI Statement(s) do not have to fit inside the box but should be placed in this area.