Nokia B66 Smart Node User Guide

NOKIA B66 Smart Node

Welcome

The Smart Node 4G provides enhanced mobile voice and data service within buildings. It delivers high-quality voice calls and faster, more reliable mobile data service.

The Smart Node connects to your broadband Internet service to deliver an extended indoor mobile network coverage. The in-building mobile phone connectivity, signal quality, and data bandwidth will greatly improve, especially if the building is in a remote area or out of adequate mobile phone tower range.

Inside this packaging, you will find the Smart Node and its accessories necessary for the installation. The Smart Node has zero touch set-up process. Just install as detailed in this guide and it connects to your mobile phone automatically whenever your phone is within range.

Before you begin you need to make sure you have the following:

  • High speed internet service and an available Ethernet LAN port on your router.
  • An available power socket or electrical outlet.
  • A LTE phone registered for LTE service with your service provider.

Box Content

  • Quick Start Guide
  • Smart Node 4G Module
  • Back Haul Module (assembled with the 4G Module
  • Wall Mounting Kit (1 Bracket, 3 Screws, and 3 Wall Anchors)
  • AC Power Adaptor
  • Ethernet Cable
  • GPS Antenna

Connection Overview

All Smart Node Variants

Power
Power on when AC Adaptor is plugged in.
Yellow WAN Port
Connect to the internet router.
Grey LAN Port
Connect to other devices, like PC, if needed.
GPS Port
Connect the external GPS antenna if needed.
Reset

  1. Press and hold for 5 seconds for reboot.
  2. Press and hold for 20 seconds for factory setting reset and software update.

Quick Setup

  1. Connect your Smart Node to the Internet
    Connect the Ethernet cable from the yellow “WAN” port on your Smart Node to an available Ethernet port on your internet router.
  2. Connect GPS antenna to Smart Node
    Connect the GPS antenna cable to the GPS port. Position the antenna out side the home where sky visibility is there or place it as close to a window as possible.
  3. Power on your Smart Node
    Plug in your AC power adaptor into the power outlet and connect the power cable to the Smart Node power port.
  4. Let your Smart Node
    After you power on your Smart Node, it will go through self- installation. It can take up to 45 minutes to complete the device setup. Your Smart Node may download updates and restart during this time.
    • Power (Solid White)
      Power on. Device self-testing and update complete.
    • Internet (Solid White)
      Successful internet connection.
    • Status (Solid White)
      Successful connection established with mobile operator network.
    • GPS (Solid White)
      Successful connection established with the Global Satellite System
    • 4G C1 (Solid White)
      Device is ready to provide 4G service for Carrier 1.
    • 4G C2 (Solid White)
      Device is ready to provide 4G service for Carrier 2.
    • 4G C2 is off/unlit in case only one LTE cell is enabled.
      Device is ready to provide 4G service for Carrier 2.
  5. Flexible mount options are available for the Smart Node
    • Wall mounting (accessories included in the box)
    • Ceiling mounting (accessories included in the box)
    • Desk stand (not included in the box, Optional accessory) Mount the Smart Unit as needed.

Congratulations! Your Smart Node setup is complete.
You should see improved signal strength from your device. Make your first call to enjoy more dependable voice calls and more reliable high- speed data connection.

Common Troubleshooting Procedures

Issue Description and Resolution Power Internet Status GPS 4G CH1 4G CH2
Device has a hardware issue. Solid Orange Solid Orange  Solid Orange Solid Orange Solid Orange Solid Orange/O

ff

Tamper Detected

Product has a temper alarm. Radio and all other components have been turn off

    Solid Orange    Solid Orange    Solid Orange    Flashing Orange    Flashing Orange  Flashing Orange/of f
Network Attach failure

Device could not access local network (Ethernet or DHCP failure, could not reach SeGW).

  Solid White  Solid orange  Off  Any  Off  Off
Failed to contact SeGW

Unit completed DHCP but could not contact the SeGW.

  Solid White  Flashing Orange  Off  Any  Off    Off
SeGW authentication failure.

Unit contacted SeGW but failed.

  Solid White  Solid White  Solid Orange  Any  Off  Off
4G FGW Connection failure

Failed to connect to the 4G Femto Gateway.

  Solid White  Solid White  Flashing Orange  Any  Off  Off
LTE at full capacity

LTE cell has reached configured maximum number of UEs.

  Any  Any  Flashing White  Any  Flashing White  Off
No GPS Signal

Device is not able to capture GPS signal.

  

Any

  

Any

  

Any

  

Solid Orange

  

Any

  

Off

Searching for satellites Any Any Any Flashing white Any Off
Environment failure

The device is overheated.

Move device to a cooler location.

 Flashing Orange Flashing Orange Flashing Orange Flashing Orange Flashing Orange Flashing Orange/off

FAQs

How do I know that I am using my Smart Node service?
Your mobile phone display will automatically indicate if you are within small cell signal range. If registered and configured properly, your mobile phone should display a small cell service message and an associated signal indicator.

Will my call drop if I leave the building in the middle of a call?
If you move out of range of the Smart Node, your call will be automatically transferred to the next available network service offered by your mobile service provider, without disconnecting your call. If no other mobile network is available your call will be disconnected.

What happens if my broadband connection fails?
If you lose your broadband connection in cases of IP connectivity set up failure, the Internet light will light solid orange and your Smart Node coverage will stop. The Smart Node service will return when the broadband connection is recovered.

What happens if my Smart Node stops operating – can I still place a call?
If your Smart Node stops operating (e.g. if you have lost your broadband connection) then you will no longer be able to place calls through the Smart Node. However, if you have coverage from the mobile network of your mobile service provider you can still place calls normally.

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate
the equipment.

RF Exposure Information

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

NOTICE OF LIABILITY: Every effort has been made to ensure that this guide contains accurate and current information. However, Nokia and the author shall not be liable for any loss or damage suffered by readers as a result of any
information contained herein.

TRADEMARKS: Nokia and the Nokia logo are registered trademarks of Nokia.
All other trademarks are the property of the
respective owners.
20210607

Copyright © 2021 Nokia. All rights reserved.
The information presented is subject to change without notice. Nokia assumes no responsibility for inaccuracies contained herein.