Philips TAT5506 Wireless Sports Earbuds User Manual

PHILIPS TAT5506 Wireless Sports Earbuds User Manual

1. Important safety instructions

Hearing Safety

Danger

To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your headphones.

Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume continuously upwards as your hearing adapts.
Do not turn up the volume so high that you can’t hear what’s around you.
You should use caution or temporarily discontinue use in potentially hazardous situations.
Excessive sound pressure from earpieces and headphones can cause hearing loss.
Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Caution

Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping, splashing water.
Do not allow your headphones to be submerged in water.
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

About operating and storage temperatures and humidity

Store in a place where temperature is between -20°C (-4°F) and 50°C (122 °F) (up to 90% relative humidity.
Operate in a place where temperature is between 0°C (32°F) and 45°C (113 °F) (up to 90% relative humidity.
Battery life may be shorter in high or low temperature conditions.
Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);

2. Your True wireless earpieces

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips True wireless earpieces, you can:

enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.

What’s in the box

Other devices
A mobile phone or device (e.g. notebook, PAD, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the earpieces (see ‘Technical data’ on page 10).

Overview of your True wireless earpieces

Microphone
Multi-function touch
LED indicator (earpieces)
Microphone
LED indicator (factory reset)
Factory reset button
USB-C charging slot
LED indicator (charging box)

3. Get started

Charge the battery

Note

Before you use your earpieces for the first time, place the earpieces in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
Use only the original USB-C charging cable to avoid any damage.
Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off.

Charging Box

Connect one end of the USB cable into the charging box, and another end into the power source.

The charging box starts charging.

Charging process is verified by the blue LED light on the front panel.
When the charging box is fully charged, the blue light goes on.

Tip

The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it supports 3 times full recharge cycle for the earpieces.

Earpieces

Place the earpieces in the charging box.

The earpieces start charging.

Charging process is verified by blue LED light on the earpieces.
When the earpieces is fully charged, the blue light goes off.

Tip

Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.

Pair the earpieces with your Bluetooth device for the first time

Make sure that the headphones is fully charged and powered off.
Open the top cover from charging box.
Turn on the Bluetooth function of your Bluetooth device.
Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Note

After powering on, if the earpieces cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.

The following example shows you how to pair the earpieces with your Bluetooth device.

Turn on the Bluetooth function of your Bluetooth device, select Philips TAT5506.
Enter the earpieces password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.

Single earpiece (Mono mode)
Take either right or left earpiece out from charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from earpiece.

Note

Take the second Earpiece from the charging box and they will pair each other automatically.

Pair the earpieces with another Bluetooth device

If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices is turned off.
Long touch over 5 seconds both left & right side simultaneously with earpiece on ear, release when Pairing voice prompt is heard.

Note

The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

4. Use your earpieces

Connect the earpieces to your Bluetooth device

Turn on the Bluetooth function of your Bluetooth device.
Open the top cover from charging box.

The blue LED ashes.
The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode.

Tip

The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

Note

If the earpieces fail to connect to any Bluetooth device within 5 minutes, it will turn o automatically to save the battery life.
In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually

Control ANC (active noise cancelation)

Enable ANC

Dierent ANC mode can be toggled via double tap on the right earpiece.

ANC function is auto active when put into the ear.
Touch the MFB button twice, it will change to Awareness mode.
Touch the MFB button twice again, it will turn the ANC function o.

Tip

By removing the earpiece, it will automatically change to sleep mode. When put earpiece back, it will return to active mode.

ANC LED indicator status

Power on/off

Manage your calls and music

LED indicator status

Battery LED indicator on Bluetooth device

It will show a battery indicator on Bluetooth device after connected to earpieces.

Voice Assistant

How to wear

5. Reset the earpieces

If you encounter any pairing or connection issue, you can follow the following procedure to reset your headset

On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT5506 from the device list.
Turn off the Bluetooth function of your Bluetooth device.
Return earpieces to charging box & open the lid.
Short press twice on casing button.
Follow steps in “Use your earpieces-Connect the earpieces to your Bluetooth device.”
Pair the earpieces with your Bluetooth device, select Philips TAT5506.

6. Technical data

Music time: 7 hours
Talk time: 7 hours
Standby time: 200 hours
Charging time: 2 hours Lithium-ion battery 50 mAh on each earpiece, Lithium-ion battery 500 mAh on charging box
Bluetooth version: 5.2
Compatible Bluetooth profiles: -HEP (Hands-Free Profile) -A2DP (Advanced Audio Distribution Profile) -AVRCP (Audio Video Remote Control Profile)
Supported audio codec: SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 10 dBm
Operating range: Up to 10 meters (33 feet)
Auto power off
USB-C port for charging
Low battery warning: available

Note

Specications are subject to change without notice.

7 Notice

Declaration of conformity

Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com.

Disposal of your old product and battery

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an ocial collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.

Make sure the earpieces is disconnected from the charging box before removing the battery.
Make sure the charging box is disconnected from the USB charging cable before removing the battery.

Compliance with EMF

This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buer) and polyethylene (bags, protective foam sheet.)

Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

8. Trademarks

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Siri

Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Google

Google and Google Play are trademarks of Google LLC.

9. Frequently asked questions

My Bluetooth earpieces do not turn on.

The battery level is low. Charge the earpieces.

I cannot pair my Bluetooth earpieces with my Bluetooth device.
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces.

Pairing does not work.

Put both earpieces into charging box.
Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
On your Bluetooth device, delete “Philips TAT5506” from the Bluetooth list.
Pair your earpieces (see ‘Pair the earpieces with your Bluetooth device at the rst time’ on page 6).

The Bluetooth device cannot find the earpieces.

The earpieces may be connected to a previously paired device. Turn o the connected device or move it out of range.
Pairing may have been reset or the earpieces have been previously paired with another device. Pair the earpieces with the Bluetooth device again as described in the user manual. (see ‘Pair the earpieces with your Bluetooth device at the rst time’ on page 6).

My Bluetooth earpieces are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone. Select to listen to music through the earpieces.

The audio quality is poor and crackling noise can be heard.

The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them.
Charge your earpieces.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.
Make sure your mobile phone not only supports (mono) HFP but also supports A2DP and is BT4.0x (or higher) compatible (see ‘Technical data’ on page 10).

The right and left earpieces are disconnected from each other.

Put both earpieces into charging box, keep the cover open.
Short press 3 times casing button.

Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAT5506_

Read More About This Manual & Download PDF:

Download

Philips TAT5506 Wireless Sports Earbuds User Manual

Was this manual helpful?