Toshiba TY-ASC50 Portable Sound System User Manual
User Manual
Read this booklet thoroughly before using it and save it for future reference
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury tip-over.- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Warning To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as vases, should not be placed on the apparatus.
- An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
- Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
- Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
- Minimum distances 30cm around the apparatus for sufficient ventilation;
- The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.;
- No naked flame sources, such as lighted candles, should be placed on the apparatus;
- Attention should be drawn to the environmental aspects of battery disposal;
- The use of apparatus in moderate climates.
- WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture;
- CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type;
- Batterie shall not be exposed to excessive heat such as sunshine, fire, etc.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable;
Guide to the Appliance
Top View
1. 3.5mmAUX IN JACK | 13.▶ /TUN.+ BUTTON |
2. 6.3mm MIC JACK1 | 14. |
3. 6.3mm MIC JACK2 | 15.◀ /TUN.- BUTTON |
4. USB PORT | 16. MIC VOL. CONTROL |
5. ECHO BUTTON | 17. 10/M./FOLD.- BUTTON |
6. POWER ON/OFF BUTTON | 18.P-MODE/M. BUTTON |
7. LIGHT BUTTON | 19. CHARGE INDICATOR |
8. LCD DISPLAY | 20. PAIR INDICATOR |
9. FUNCTION BUTTON | 21. BASS BUTTON |
10. 10/M./FOLD.+ BUTTON | 22. EQ BUTTON |
11. VOLUME CONTROL | 23. USB CHARGE PORT |
12. HANDLE |
Front and Back view
24. SPEAKERS | 28. VENTILATION HOLES |
25. LED DISCO LIGHT | 29. FM ANTENNA |
26. SPEAKER GRILL | 30. TWEETER |
27. AC SOCKET |
Getting Started
POWER SOURCE
This unit works with a rechargeable lead-acid battery (the battery capacity 4000mAh). Fully charge the unit (around 7 hours) before using the product for the first time. The playback time has about 2hours after full charging. Unplug the AC Power cord from the AC socket to work on the battery pack after fully charged. Plugging the AC Power cord while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights red during charging, when the battery is fully charged the indicator will turn green. When the unit is with a low battery, the LED indicator will flash in red.
Warning: Do not change the battery, only high-qualified personnel can perform this operation.
OPERATION INSTRUCTION
BASIC FUNCTION
TURNING THE UNIT ON/OFF
Press the power ON/OFF button to switch the unit on/off.
Electrostatic Discharge hints – The unit may reset or may not reset to normal operation mode
due to electrostatic discharge, just switch it off and reconnect again.
SETTING THE FUNCTION MODE
To change the function modes, press the FUNCTION button repeatedly to choose the USB/Bluetooth/AUX/Radio function.
ADJUSTING THE VOLUME
- Rotate the VOLUME knob on the unit to increase or decrease the music volume.
- Rotate the MIC VOL. the knob on the unit to increase or decrease the microphone volume.
BASS ADJUSTMENT
Press the BASS button on the unit to increase the bass effect.
EQUALIZER (EQ) FUNCTION
This unit has a built-in equalizer system, Press the EQ button on the unit to select a setting that best matches the music style: FLAT, CLASSIC, ROCK, POP, and JAZZ.
USB CHARGING
This unit provides a 5V 1A USB charging port for charging your smartphone. Connect the USB cable of your smartphone to the USB CHARGE port for charging.
MICROPHONE ECHO ADJUSTMENT
Press the ECHO button on the unit to turn on or off the microphone echo effect.
FLASHING LIGHT
There are 5 modes for the DISCO LED lighting. Press the LIGHT button to choose the light modes. To inactivate the light, press the LIGHT button until “OFF” showed on the display.
L-1: Blue LED will be on constantly when it is selected.
L-2: Blue LED will be on flashing mode.
L-3: Red LED will be on constantly.
L-4: Red LED will be on flashing mode.
L-5: 7 colors LED will be on flashing mode.
RADIO OPERATION
Listen to FM radio broadcasts. Press the FUNCTION button on the unit, the display reads FM and the radio frequency.
Note: in order to get the best reception, extend the FM ANT. on the rear of the unit before use to its full length.
TUNING TO A RADIO STATION
If you know the station frequency that you want to tune to directly:
Tune to a station by pressing the
AUTOMATIC TUNING STOP
Press and hold the
AUTO PRESET MEMORY / SCAN
To scan for stations within reception range and save them to preset memory automatically, press and hold the /PAIR/AUTO button. After the unit is finished scanning, the unit will automatically tune to preset number 1 (P01). To tune to a preset station:
- To tune to the next preset station, press the 10/M./FOLD.+ button.
- To tune to the previous preset, press the 10/M./FOLD.- button.
MANUAL PRESET MEMORY OPERATION
Choose which stations to save in preset memory instead of scanning automatically.
- Use the
/TUN.+ or /TUN.- button to tune to the station that you want to save as a preset (e.g., 93.1). - Press the P-MODE/M. button. “
” will flash on the display to indicate that you are saving the station as Preset Memory 01. (To change the preset memory number, press the 10/M./FOLD.+ or 10/M./FOLD.-buttons.) - Press the P-MODE/M. button to finish saving the station (e.g., P01 is now set to 93.1).
- To save another station, repeat steps 1 to 3. You may save up to 30 FM stations.
USB OPERATION
This unit provides two USB ports for music playback.
- Press the FUNCTION button on the unit to select “USB” mode.
- Plug the USB memory stick into the USB port on top of the unit(The unit can support up to 32G USB devices). Playback will start automatically from Track 1.
- To pause playback, press the
/PAIR/AUTO button on the unit. The playing time will flash on the display. - To resume playback, press the
/PAIR/AUTO button again. - To select the desired track, press the
or button respectively during playing until the desired track appears on the display. The unit will start playing automatically. - To search for a particular passage during playback, press and hold the
or button to scan the current playing track at high speed until desired point (passage) appears, then release the button for normal playback mode. - To select a song whose track number exceeds 10, press the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip forward/backward 10 tracks, then press the
or button to select the desired track. - To select the desired folder (if the USB contains more than one folder), press and hold the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip forward/backward a folder, then press the
or button to select the desired track.
Important: The USB port is intended for data transfer only, other devices cannot be used with this USB connection. The use of USB extension cords is not recommended. Don’t plug the USB from the unit when playing or reading the USB device.
REPEAT PLAY
You can play one track or all tracks on the USB repeatedly.
To Repeat a Single Track
- Press P-MODE/M. button on the unit during play, the display will show “
” and the current track will be played over and over again. - To cancel repeat play, press P-MODE/M. button on the unit until “
” disappears from the display.
To repeat all the Tracks
- Press P-MODE/M. button on the unit until the “
” shows steadily on the display, all tracks on the USB will be played over and over again. - To cancel repeat play, press the P-MODE/M. button on the unit until “
” disappears from the display.
To repeat the folder (only for USB which contains more than one folder)
- Press the P-MODE/M. button on unit until “
FOLDER ” shows steadily on the display, the current folder will be repeated over and over again. - To cancel repeat play, press the P-MODE/M. button on unit until “
FOLDER” disappears from the display.
RANDOM PLAY
Press the P-MODE/M. button on the unit in play mode till the “RAND” shows steadily on the display, the random play will start from the next track automatically. Press the P- MODE/M. button on the unit again until the “RAND” disappears from the display to cancel.
BLUETOOTH OPERATION
- Press the FUNCTION button on the unit to switch to the BLUETOOTH function, the LCD will display “ ” and the pairing indicator will flash at high speed.
- Turn on the Bluetooth function on the device, scan the unit “KP626T” and connect, then input the password 0000 if required, the pairing indicator keep light up to indicate connection done, and the display will show “ ” steadily. Press Play to start playback.
- Rotate the VOLUME knob on the unit or adjust the volume on the external device to increase or decrease the music volume to your desired level.
- Press and hold the
/PAIR/AUTO button to disconnect Bluetooth.
Note: The Bluetooth works best within 10 meters in the open air.
AUX-IN OPERATION
- Press the FUNCTION button on the unit to select the “AUX” mode.
- Connect your audio device to the AUX IN jack on the top panel of the unit with an AUX-IN cable.(audio cable is not included)
- Rotate the VOLUME knob on the unit or adjust the volume on the external device to increase or decrease the music volume to your desired level.
- Control the playback with your audio device.
MIC JACK OPERATION
The microphone input is available in all modes.
- Connect your microphone to the 6.3mm MIC JACK found on the top panel of the unit.
- Rotate the MIC VOL. the knob on the unit to increase or decrease the microphone volume.
- Press the ECHO button to turn on or off the echo effect of the microphone.
Technical Specifications
GENERAL
Power Requirements | AC100-240V~60/50Hz |
Battery type | Built-in rechargeable battery, 4000mAh/12V, lead-acid |
Power consumption | 40W |
Power output | 25W X 2 |
FM frequency | FM 87.5-108 MHz |
AUX-in jack | 3.5mm |
Microphone jack | 6.3mm |
Work temperature | 5°C – +35°C |
USB memory section | |
Playback format | WMA/MP3 |
Memory | 32MB to 32GB |
Bluetooth | |
Communication system | Bluetooth Standard version 5.0 |
Reception Range | 10 meter (line-of-sight distance) |
Compatible Bluetooth profiles | Advanced Audio Distribution Profile (A2DP) |
ACCESSORIES
Instruction Manual x 1pc
AC Cord x 1pc
Microphone x 1pc
Note: Specifications are subject to change for continuous improvement without prior notice.