Motorola MR-01 Remote Control User Manual

motorola MR-01 Remote Control User Manual

Operation

  1. Turn on Bluetooth function of mobile phone
  2. At the same time, press the “OK” and “return” keys of the remote control. The indicator light will be lit and then extinguished. After 3 seconds, the red light will flash slowly, and the remote control will enter the broadcast scanning mode (you can release the button after entering).
  3. Select the Bluetooth device mr-01 on the mobile phone to connect
  4. After the connection is successful, the red light of the remote control will stay on for 2 seconds, and then exit the pairing mode and the indicator light will go off.
  5. If the connection is not successful, the red light will continue to
    blink. After 30 seconds, the red light will be off when the matching
    mode is out.

Key description

Key name

 Key Icon

Operation and function

Home page

 click：Home page
chooser

click：host standby

Mute

 click：Mute
menu

click：Hang up

Circle

 click：answer the phone
up

click：Up

down

 click：Down
left

click：Left

right

 click：Right
OK

click：Confirm

return

 click：Return
mouse

click：Mouse On/Off

Volume down

 click：Volume down
Volume up

click：Volume up

Use the mouse

Mouse On When there is a link, click the empty mouse button on the remote control
Mouse Off Click the mouse button to close the empty mouse
Left mouse button The OK key responds to the left mouse button function
User calibration and sensitivity adjustment
  1. At the same time, press and hold the “volume plus + and volume -” indicator light always on — > put the remote control in place for 3 seconds, the red light will flash quickly (100ms on and 100ms off) to start calibration (calibration time is 5 seconds), the red light will always be on if calibration is successful (it will exit automatically after 10 minutes or press any key to exit), and the red light will go out if calibration fails
  2. Mouse + volume plus sensitivity up
  3. Mouse + reduced sensitivity
  4. Mouse speed adjustment is divided into five gears, the default is in the middle gear

Low power prompt

*Two 7 dry batteries are used for power supply
*Low power detection and prompt

  1. Vbat < = 2.4V indicates low power,
  2. When Vbat < = 2.2V, it is forbidden to work, and it can only be restored after power on again. When the forbidden working voltage is detected, the red light will flash rapidly for 10 seconds, and then it will enter the forbidden mode, which can work normally within 10 seconds,

Indicator light description

  • No Bluetooth link: press the remote control indicator to flash twice
  • Bluetooth link success status: click the indicator to flash once

FCC warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

IC warning:

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)

This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment.